3545 cadillac avenue ? costa mesa, ca 92626-1401 ? (714) 433-1200 ? fax (714) 433-1234 marketing bulletin date: august 25, 2005 to: all sales personnel from: mark stoner re: product termination to all concerned parties, this bulletin is to notify all customers of the discontinuation of the following ecliptek series effective august 25 th , 2005: series description recommended replacement E31J2 5v 6 pad smd lvpecl vcxo e32d1 e32j2 3.3v 6 pad smd lvpecl vcxo e32d1 in compliance with our end of life (eol) policy, this will serve as advanced notice of product termination. new orders will not be accepted after november 25 th , 2005, with delivery to conclude by february 25 th 2006. if there are any questions pertaining to this bulletin, please fell free to contact me. thank you again for your cooperation. best regards, mark w. stoner director of marketing ecliptek corporation
E31J2 series ? pecl output vcxo 5.0v supply voltage 6 pad pcb smd package with j-leads stability to 20ppm output enable/disable available complementary output available available on tape and reel h 5.9 l 14.8 w 10.2 oscillator E31J2 800-ecliptek www.ecliptek.com for latest revision 192 specifications subject to change without notice. manufacturer category series package voltage class rev . date ecliptek corp. oscillator E31J2 6-pcb-j 5.0v os74 01/03 electrical specifications 19.440mhz to 212.500mhz 0c to 70c or -40c to 85c -55c to 125c 5.0v dc 5% 100ma maximum 100kh 50ppm, 25ppm, or 20ppm maximum v cc -1.025v dc minimum v cc -1.620v dc maximum 2 nseconds maximum 50 10(%) 50 5(%) 50 ohms into v cc -2.0v dc no connect and single output enable/disable and single output no connect and complementary output or enable/disable and complementary output enables output enables output disables output: logic low disables complementary output: logic high 10 mseconds maximum 1 psec maximum 50ppm minimum 20%, 15%, or 10% maximum 2.5v dc 2.0v dc 0.0v dc to v cc 2.5v dc positive transfer characteristic 50kohms typical 10khz minimum frequency range operating temperature range storage temperature range supply voltage (v cc ) input current logic type frequency tolerance / stability output voltage logic high (v oh ) output voltage logic low (v ol ) rise time / fall time duty cycle load drive capability additional output / logic control enable/disable input voltage start up time rms phase jitter absolute pull range (apr) linearity control voltage (v c ): test conditions for apr control voltage range (v cr ) center control voltage transfer function input impedance modulation bandwidth inclusive of operating temp range, supply voltage, load, and aging @25c over 10 years 20% to 80% of waveform at 50% of waveform v il of v cc -1.475v dc maximum no connection v ih of v cc -1.165v dc minimum fj = 12khz to 20mhz inclusive of operating temp range, supply voltage, load, and aging @25c over 10 years at -3db with control voltage of +2.5v dc
characteristic specification seal integrity bubble test in perfluorocarbon at +125c 5c for 60 seconds minimum (internal crystal only). solderability sn63 solder dip at +230c 5c for 5 seconds/95% coverage. marking permanency 10 strokes with brush after 1 minute soak in solvent, 3 times. shock random drop on hard wooden plate 3 times from a height of 20cm. vibration frequency with an amplitude of 1.5mm sweeping between 10hz to 55hz within 1 minute (approximately) for 2 hours minimum on each axis (x, y and z) for a total of 6 hours. line 1: ecliptek line 2: xx.xxx m frequency in mhz (5 digits maximum + decimal) line 3: xx y zz week of year last digit of year ecliptek manufacturing identifier manufacturer category series package voltage class rev . date ecliptek corp. oscillator E31J2 6-pcb-j 5.0v os74 01/03 mechanical dimensions all dimensions in millimeters environmental/mechanical specifications marking specifications tape and reel dimensions all dimensions in millimeters *compliant to eia 481a suggested solder pad layout all dimensions in millimeters tolerances = 0.1 800-ecliptek www.ecliptek.com for latest revision 193 specifications subject to change without notice. reel m 1.5 min n 50 min o 20.2 min p 13.2 q 40 min s 10 min r 2.5 min t 30.4 max u 360 max v 24.4+2-0 qty/reel 1000 a b c d e f 24 .3 11.5 .1 10.75 .1 4 .2 2.1 f g h j k l 12 .1 b0* 1.5 +.1-0 a0* .4 .05 k0* tape part numbering guide top view side view front view pin 1: voltage control pin 2: enable/disable or no connect pin 3: case ground pin 4: output pin 5: complementary output or no connect pin 6: supply voltage E31J2 f 3 a 2 c - 155.520m tr available options blank=tubes tr = tape and reel (standard) frequency additional output/logic control a=no connect and single output b=enable/disable and single output c=no connect and complementary output d=enable/disable and complementary output duty cycle 1=50 10(%), 2=50 5(%) frequency tolerance & stability/ operating temperature range d=50ppm maximum over 0c to +70c e=25ppm maximum over 0c to +70c f=20ppm maximum over 0c to +70c h=50ppm maximum over -40c to +85c apr 3=50ppm minimum linearity a=20% b=15% c=10%
e32j2 series ? pecl output vcxo 3.3v supply voltage 6 pad pcb smd package with j-leads stability to 20ppm output enable/disable available complementary output available available on tape and reel h 5.9 l 14.8 w 10.2 oscillator e32j2 800-ecliptek www.ecliptek.com for latest revision 194 specifications subject to change without notice. manufacturer category series package voltage class rev . date ecliptek corp. oscillator e32j2 6-pcb-j 3.3v os73 01/03 electrical specifications 19.440mhz to 212.500mhz 0c to 70c or -40c to 85c -55c to 125c 3.3v dc 5% 75ma maximum 100kh 50ppm, 25ppm, or 20ppm maximum v cc -1.025v dc minimum v cc -1.620v dc maximum 2 nseconds maximum 50 10(%) 50 5(%) 50 ohms into v cc -2.0v dc no connect and single output enable/disable and single output no connect and complementary output or enable/disable and complementary output enables output enables output disables output: logic low disables complementary output: logic high 10 mseconds maximum 1 psec maximum 50ppm minimum 20%, 15%, or 10% maximum 1.65v dc 1.35v dc 0.0v dc to v cc 1.65v dc positive transfer characteristic 50kohms typical 10khz minimum frequency range operating temperature range storage temperature range supply voltage (v cc ) input current logic type frequency tolerance / stability output voltage logic high (v oh ) output voltage logic low (v ol ) rise time / fall time duty cycle load drive capability additional output / logic control enable/disable input voltage start up time rms phase jitter absolute pull range (apr) linearity control voltage (v c ): test conditions for apr control voltage range (v cr ) center control voltage transfer function input impedance modulation bandwidth inclusive of operating temp range, supply voltage, load, and aging @25c over 10 years 20% to 80% of waveform at 50% of waveform v il of v cc -1.475v dc maximum no connection v ih of v cc -1.165v dc minimum fj = 12khz to 20mhz inclusive of operating temp range, supply voltage, load, and aging @25c over 10 years at -3db with control voltage of +1.65v dc
characteristic specification seal integrity bubble test in perfluorocarbon at +125c 5c for 60 seconds minimum (internal crystal only). solderability sn63 solder dip at +230c 5c for 5 seconds/95% coverage. marking permanency 10 strokes with brush after 1 minute soak in solvent, 3 times. shock random drop on hard wooden plate 3 times from a height of 20cm. vibration frequency with an amplitude of 1.5mm sweeping between 10hz to 55hz within 1 minute (approximately) for 2 hours minimum on each axis (x, y and z) for a total of 6 hours. line 1: ecliptek line 2: xx.xxx m frequency in mhz (5 digits maximum + decimal) line 3: xx y zz week of year last digit of year ecliptek manufacturing identifier manufacturer category series package voltage class rev . date ecliptek corp. oscillator e32j2 6-pcb-j 3.3v os73 01/03 mechanical dimensions all dimensions in millimeters environmental/mechanical specifications marking specifications tape and reel dimensions all dimensions in millimeters *compliant to eia 481a suggested solder pad layout all dimensions in millimeters tolerances = 0.1 800-ecliptek www.ecliptek.com for latest revision 195 specifications subject to change without notice. reel m 1.5 min n 50 min o 20.2 min p 13.2 q 40 min s 10 min r 2.5 min t 30.4 max u 360 max v 24.4+2-0 qty/reel 1000 a b c d e f 24 .3 11.5 .1 10.75 .1 4 .2 2.1 f g h j k l 12 .1 b0* 1.5 +.1-0 a0* .4 .05 k0* tape part numbering guide top view side view front view pin 1: voltage control pin 2: enable/disable or no connect pin 3: case ground pin 4: output pin 5: complementary output or no connect pin 6: supply voltage e32j2 f 3 a 2 c - 155.520m tr available options blank=tubes tr = tape and reel (standard) frequency additional output/logic control a=no connect and single output b=enable/disable and single output c=no connect and complementary output d=enable/disable and complementary output duty cycle 1=50 10(%), 2=50 5(%) frequency tolerance & stability/ operating temperature range d=50ppm maximum over 0c to +70c e=25ppm maximum over 0c to +70c f=20ppm maximum over 0c to +70c h=50ppm maximum over -40c to +85c apr 3=50ppm minimum linearity a=20% b=15% c=10%
|
